Fire Resisting Cable

Fire Resisting Cables

Fire Resistant Signal & Data Cables

Fire resistant UTP Cat 5 Data Cables

FFX-CAT5UTP4P24FR

Application

The cables are desgined for structure wiring, compatible with all known connection systems according to EN

50173. Based on the design for structured wiring (found in IEC 61156 and BS EN 50288), this cable brings

together high frequency data transmission and circuit integrity in four pair cable that will continue to transmit

data even when being directly attacked by fire.

Standards

Basic design to EN50173

FFX-CAT5UTP4P24FR

Fire Performance

Circuit Integrity

IEC 60331-23; BS 6387 CWZ; DIN VDE 0472-814(FE180);

CEI 20-36/2-1; SS229-1; NBN C 30-004 (cat. F3);

NF C32-070-2.3(CR1)

System circuit integrity DIN 4102-12, E30 depending on lay system

Flame Retardance (Single Vertical

Wire Test)

EN 60332-1-2; IEC 60332-1-2; BS EN 60332-1-2; VDE 0482-332-1 ; NBN C

30-004 (cat. F1); NF C32-070-2.1(C2);

CEI 20-35/1-2; EN 50265-2-1*; DIN VDE 0482-265-2-1*

Reduced Fire Propagation

(Vertically-mounted

bundled wires & cable test)

EN 60332-3-24 (cat. C); IEC 60332-3-24; BS EN 60332-3-24; VDE 0482-332-3; NBN

C 30-004 (cat. F2); NF C32-070-2.2(C1); CEI 20-22/3-4; EN 50266-2-4*; DIN VDE

0482-266-2-4

Halogen Free

IEC 60754-1; EN 50267-2-1; DIN VDE 0482-267-2-1;

CEI 20-37/2-1 ; BS 6425-1*

No Corrosive Gas Emission

IEC 60754-2; EN 50267-2-2; DIN VDE 0482-267-2-2;

CEI 20-37/2-2 ; BS 6425-2*

Minimum Smoke Emission

IEC 61034-1&2; EN 61034 -1&2; DIN VDE 0482-1034-1&2;

CEI 20-37/3-1&2; EN 50268-1&2*; BS 7622-1&2*

No Toxic gases NES 02-713; NF C 20-454

Note: Asterisk * denotes superseded standard.

Voltage Rating

60V

Cable Contruction

Conductors: Plain annealed copper wire, solid according to IEC(EN) 60228 class 1.

Insulation: PE wrapped with fire resistant silicone rubber compound type EI2 as per BS 7655-1.1.

Twisted Pairs: Insulated conductors are twisted into pairs with varying lay length to minimize crosstalk.

Cabling Elements: Insulated cores are twisted to form pairs with varying lay length to minimize crosstalk. Two-

pair cable had four cores laid in quad formation.

Cabling: Pairs are cabled together in concentric layers.

Outer Sheath: Thermoplastic LSZH compound type LTS3 as per BS 7655-6.1 (Thermosetting LSZH compound

type SW2-SW4 as per BS 7655-2.6 can be offered.)

Physical And Thermal Properties

Temperature range during operation (fixed state): -5°C - +50°C

Temperature range during installation (mobile state): -20°C - +90°C

Minimum bending radius: 8 x Overall Diameter

Electrical Properties

Characteristic Impedance:100 Ohm±15%

Nominal Velocity of Propagation (NVP):69%

Max. Dc Resistance:9.38 Ohm/100m

Max. Resistance Unbalance:5%

Max. Mutual Capacitance::5.6 nF/100m

Maximum Capacitance Unbalance:330 pF/100m

Max. Propagation Delay Skew:30 ns/100m

Max. Propagation Delay:536 ns/100m@100 mhz

Max. Pulling Load:80N

Electrical Properties

Characteristic Impedance:100 Ohm±15%

Nominal Velocity of Propagation (NVP):69%

Max. Dc Resistance:9.38 Ohm/100m

Max. Resistance Unbalance:5%

Max. Mutual Capacitance::5.6 nF/100m

Maximum Capacitance Unbalance:330 pF/100m

Max. Propagation Delay Skew:30 ns/100m

Max. Propagation Delay:536 ns/100m@100 mhz

Max. Pulling Load:80N

Construction Parameters

Cable Code Conductor Diameter Nominal Insulation Thickness Nominal Overall Diameter
mm mm mm
FFX-CAT5UTP4P24FR 0.5 0.25 5.3